Construction & Masonry Products

Acro Seal-CFV is a Nano-enhanced water repellent and sealer. This is a water-based, water-proofing sealer and repellent for awnings, tents, and outdoor canvas, fabric, and vinyl-type siding, fencing, signs and other vinyl materials. Acryl Seal-CFV protects against moisture, weathering, and staining due to heavy humidity, rain, heat, and pollutants.

Basic Features

  • Water & stain, resistant. From deicing salts, rain, and pool chemicals while at the same time reducing the effects of stains from weathering and aging.
  • Resistant to freeze/thaw cycle.
  • Provides excellent chemical resistance and protection from oils, acids, chemicals, greases, solvents, and salts.
  • For all exterior canvas, fabric and vinyl surfaces.
  • Helps reduce aging, UV damage, discoloration, and staining.
  • Provides protection against moisture and fading.
  • Eco-friendly and biodegradable.
  • Non-toxic, eco-friendly, and VOC-compliant.
  • Completely non-flammable.
  • Safe to use in closed areas.
  • Can be applied in multiple coats.
  • Dries tack free and leaves a clear, skid-resistant surface.
  • Non yellowing, UV stable, and odorless.
  • Extends the life of material, keeps it flexible and clean, and maintains original appearance.
  • Exceeds ASTM Standards.

APPLICATION

PREPARATION

Surface should be free of all dust, debris, oil, and stains.

New Material

Make sure surface is clean and completely dry before product is applied. Apply directly to a completed installation.

Existing Material

Pre-clean with Bio Safe-CFV cleaner to clean and grime, rust stains, lime, brown stains, organic stains, yellowing, water stains, scale, and chalking. Scrub with soft nylon bristle brush and rinse with a low psi hot or cold water rinse. Repeat this cleaning process as needed until surface is clean. Wait until the surface is completely dry and moisture-free before application of Acro Seal-CFV.

Mixing Instructions

Mix or shake gently prior to application. Gently mix for 3‒5 minutes. Do Not Mix Vigorously. (This can introduce air bubbles and foam.)

APPLICATION METHOD

All repairs must be completed before prior to application of this product.

Use a roller, brush, or sprayer to apply product. Apply second coat if necessary. Two coats are recommended on porous surfaces.

COVERAGE RATE/CURING TIME

Exact coverage will depend upon the porosity and type of the material. Dry-to-touch in 2 hours; Initial cure will take 10‒12 hours; for maximum cure will require up to 24-48 hours. Apply second coat if necessary. Two coats are recommended on porous surfaces.

Type of Material Estimated Coverage
(1st Coat)
Estimated Coverage
(2nd Coat)
Canvas (solid) 300‒500 sq ft/gallon 600‒800 sq ft/gallon
Canvas (porous) 250‒400 sq ft/gallon 500‒700 sq ft/gallon
Vinyl (solid) 300‒500 sq ft/gallon 600‒800 sq ft/gallon
Vinyl (porous) 250‒400 sq ft/gallon 500‒700 sq ft/gallon
Fabric 200‒300 sq ft/gallon 500‒700 sq ft/gallon

 

Note: New canvas, vinyl, and fabric materials may yield higher coverage rates.

CLEAN UP

Use soap and water to clean tools and equipment.

STORAGE AND HANDLING

Not recommended to be used at, or below, 40°F. Test all surfaces for suitability. Keep off glass surfaces, if contact occurs clean immediately with soap and water. DO NOT dilute or alter the product. Protect and cover glass, metal, and surrounding surfaces from overspray.

Keep product away from skin and eyes. Do not swallow or ingest this product. The use of rubber, neoprene, nitrile, or other protective gloves is required where prolonged or extensive use is expected. Remove contaminated clothing and DO NOT wear again until thoroughly cleaned. Wash hands thoroughly with soap and water after handling.

Keep container closed when not in use. Store out of direct sunlight. Keep from Freezing. Avoid temperatures above 100 °F, or below 40 °F. Product can be stored up to 12 months. If product is stored for a long time, lightly agitate, before use.

Note: Follow directions carefully. Always consult your dealer or supplier for timing, methods and to customize application, depending on contaminations.

Biodegradable and Safe to use. Aluminum Fiberglass & Vinyl Siding Cleaner will not damage roof, gutter or landscaping, use as directed. Dilute accordingly as label instructions for best results.

It safely cleans hard surfaces: Excellent cleaning and stain removing capability formulated with Eco-friendly detergent and cleaning additives that will not damage siding surface. Dilute with water for easy and immediate application. Can be used with power washer or manual hand wash cleaning application. It goes to work immediately and quickly cleans and removes stubborn stains and soil from siding surfaces.

AFV Siding Cleaner contains a synergized blend of lipase organisms. This blend has been selected for the accelerated degradation of organic materials that builds up on the surface over time and for the degradation capabilities of various organic stains. Contains blends of enzymes provide an effective and continuous cleaning. 

REMOVES

Dirt Grass Stains
Light Rust Pollution Stains
Grime Spider Webs
Pollen Bird & Insect Droppings

Directions

 

GENERAL CLEANING

Make a test panel before general cleaning. Protect and test all non-intended surfaces.

May be diluted 1:5 for heavier stains to 1:10 for general cleaning.

FOR MANUAL HAND WASHING & CLEANING

  • Pre-wet the cleaning surface with the water first.
  • Apply diluted AFV Siding Cleaner with a soft-bristle cleaning brush or sponge. 
  • Clean one entire row at a time. 
  • Start at the bottom to avoid streaking and use garden hose to spray and rinse off each section before it dries. 

CLEANING WITH PRESSURE WASHER

  • Prewet surface.
  • Spray diluted cleaner as directed. Do not let cleaning solution dry on the surface.
  • Let cleaner set on surface approximately 60 seconds and rinse with pressure washer to clean.
  • If the stain/spot remains, repeat the above steps until the stain/spot disappears.

Note: Avoid using highly-abrasive scrubbers or steel wool. These can cause damage when cleaning vinyl siding. Do not spray or clean when siding is very hot and avoid direct sunlight on the siding to minimize streaking and water spots.

STORAGE AND HANDLING

Keep product away from skin and eyes. Do not swallow or ingest this product. The use of rubber, neoprene, nitrile, or other protective gloves is required where prolonged or extensive use is expected. Remove contaminated clothing and DO NOT wear again until thoroughly cleaned. Wash hands thoroughly with soap and water after handling. 

Keep container closed when not in use. Store out of direct sunlight. Keep from Freezing. Avoid temperatures above 100 °F, or below 40 °F. Product can be stored up to 12 months. If product is stored for a long time, lightly agitate, or shake well before use. This product is biodegradable and eco-friendly.

 Note: Follow directions carefully. Always consult your dealer or supplier for timing, methods and to customize application, depending on contaminations.

PRODUCT DESCRIPTION

Anti-Graffiti Coating-WB is a water-based, penetrating, waterproofing sealer fusion with Nano drivers, designed to protect and penetrate deep in to concrete surfaces, decks, pavement, parking structures, ramps, walls, concrete floors, and fiberglass surfaces. Anti-Graffiti Coating–WB protects against moisture, weathering, the adverse corrosive effects of de-icing salt, spalling of concrete, and all types of paint and graffiti.

FEATURES

  • Water-based, VOC-compliant (Volatile Organic Compound)
  • Skid-resistant; dries tack free
  • Long-lasting protection for new and old concrete
  • Non-yellowing, UV stable
  • Prevents spalling, and provides moisture protection
  • Use Indoors and/or outdoors
  • Repels spray paint, permanent markers, ink, and graffiti

RECOMMENDED USES

  • Any concrete—broom or smooth finish
  • Parking structures
  • Precast concrete
  • Lane barriers
  • Concrete blocks and bricks
  • Exposed aggregate
  • Bricks and natural stones
  • Porous fiberglass surfaces

Directions

New Concrete: Concrete surface should be well cured; surface should be dry, and free of all dust, derbies, oil, and tar. All joint sealants, caulking, and patching should be in place before application.

Old Concrete: Remove dirt, oil, tar, and loose spall and concrete. Patch before applying Anti-Graffiti Coating -WB.  Surface must be dry before application.

Equipment: Roller brush or low-pressure sprayer.

Application: Apply with a fine mist; follow up with coarse spray evenly over same area. For spalled areas, a second coarse spray is recommended.

Floors: For wet-look shine (hi-gloss), three or more coats may be required, depending upon type of concrete surface. Allow 4 or more hours of drying time between each coat.

COVERAGE RATE*

Concrete (Broom finish) 150–175 sq ft/gal Concrete Blocks 75–100 sq ft/gal
Concrete (smooth) 200–250 sq ft/gal Brick (Red or White) 200–250 sq ft/gal
Exposed Aggregate 175–200 sq ft/gal Fiberglass 300–400 sq ft/gal

*Exact coverage will depend upon the porosity of the surface and density of the concrete.

Clean Up: Use warm water and soap.

PACKAGING and AVAILABILITY: 1-gal and 5-gal jugs, and 55-gal pails. FOB our dock Kansas City, Kansas.

LIMITED WARRANTY:  EST Inc. has no control over the storage, handling or use of this product, thus the guarantee is limited to the purchase price of the defective material only.

PRODUCT DESCRIPTION

Aqua Seal-25 Nano-Based Graffiti Coating is a water-based, waterproofing sealer fused with nano drivers, designed to penetrate deep in to concrete, masonry, and fiberglass surfaces. A penetrating sealer, it protects concrete surfaces, decks, pavement, parking structures, ramps, walls, concrete floors, and fiberglass surfaces. Aqua Seal-25 protects against moisture, weathering, corrosive effects of de-icing salt, and spalling of concrete. It also resists all types of paint and graffiti.

FEATURES

  • Water based; VOC complaint
  • Use Indoor or outdoor
  • Non-yellowing; UV stable
  • Skid resistant
  • Dries tack-free
  • Prevents spalling; provides protection against moisture
  • Long lasting protection for new and old concrete
  • Repels spray paint, permanent markers, ink, and graffiti.

RECOMMENDED USES

  • Any concrete structure
    (Broom or smooth finish)
  • Parking structures
  • Lane barriers
  • Precast concrete
  • Concrete blocks and bricks
  • Exposed aggregate
  • Bricks and natural stones
  • Porous fiberglass surfaces

DIRECTIONS

Equipment: Roller brush or low-pressure sprayer.

Application: Apply Aqua Seal-25 with fine mist then follow up with an even, coarse spray over same area.  For spalled areas, a second coarse spray is recommended.

Floors: For a wet-look shine (hi-gloss), three or more coats may be required depending on type of concrete surface. Allow 4 or more hours of drying time between each coat.

New Concrete: Concrete surface should be well cured; surface should be dry, and free of all dust, debris, oil, and tar. All joint caulking and patching should be in place before applying Aqua Seal-25.

Old Concrete: Remove dirt, oil, and tar. Remove loose spall, concrete, and patch before applying Aqua Seal-25. Surface must be dry before application.

COVERAGE RATE*

Concrete (Broom finish) 150-175 sq ft/gal
Concrete (smooth) 200-250 sq ft/gal
Exposed Aggregate 175-200 sq ft/gal
Concrete Blocks 75-100 sq ft/gal
Brick (Red or White) 200-250 sq ft/gal
Fiberglass 300-400 sq ft/gal

*Exact coverage will depend upon the porosity of the surface and density of the concrete.

Aqua Seal-25 Nano-Based Graffiti Coating (cont.)

CLEAN UP: Use warm water and soap.

PACKAGING: 1-gal, 5-gal, and 55-gal.

AVAILABILITY: FOB our dock Olathe, Kansas.

LIMITED WARRANTY

EST Inc. has no control over the storage, handling or use of this product, thus the guarantee is limited to the purchase price of the defective material only.

Asphalt, Tar & Grease Remover is excellent for cleaning tar, asphalt, grease, oil stains and black tire marks from:

Brick. Stone. Concrete Masonry. Metal.

Can be used in Parking Garages, Parking Lots, Driveways, Mechanic Shops, Airport Runways, Highways, anywhere tar, grease and asphalt stains occur.

DIRECTIONS

Step 1. Designed to remove excess oil and grease from the top surface.

Note: Test and protect surrounding area from overspray.

  1. Brush or spray asphalt remover liberally.
  2. Let set for 2‒3 minutes.
  3. Re-apply cleaner, brushing stained areas vigorously. Use a nylon or hard bristle brush.
  4. Rinse off with water. 
  5. Repeat steps 1–4 until surface deposits are removed.

Step 2. Use EST’s Heavy-Duty Concrete Cleaner to remove embedded and penetrated stains.

  1. Designed to lift off stains and oil that penetrated deeper into the surface; Use this cleaner to remove excess oil and grease that has penetrated deeper into the surface. 
  2. Depending on the stains’ age and penetration depth, 2–3 applications may be needed to remove all the deeper stains from the surface.

Please follow EST’s Heavy-Duty Concrete Cleaner TDS or label for details on how to use the product.

Note: High-pressure rinse recommended for highly porous surface. For interior surfaces, rinse water may be applied with a stiff brush. Remove embedded stains with agitation.

ENZYMATIC CLEANER CONCENTRATE

It safely cleans hard surfaces: concrete masonry, tiles, fiberglass, plastic, and stone surfaces. It is diluted with water for easy, immediate application. Can be used daily for great continuous cleaning. It goes to work immediately—absorbs, emulsifies, and floats soil away. This product is biodegradable and eco-friendly. 

This product contains a synergized blend of lipase organisms. This has been selected for the accelerated degradation of organic materials that builds up on the surface over time. 

The lipase enzymes provide an effective means of hydrolyzing fats, oils, and grease. These selective enzymes have been selected for the degradation capabilities of organic compounds such as protein, starch, and various organic stains. 

REMOVES Surfaces Stains:

Grease Oil  Creosote 
Carbon Inks Dye
Wax Food Stains Other Stubborn Soils

ADVANTAGES

DEEP CLEANS Contains Enzymes and a deep penetrating emulsifier that penetrate and float away even the most stubborn grease and soils.
EASY TO USE May be mopped, sprayed or wiped on metals, plastic, rubber and concrete.
WATER SOLUBLE Powerful. Mixes with water for fast, safe cleaning action. May be diluted with 1–15 parts of water.
SAFE ON
METAL SURFACES
Contains a special rust inhibitor. Also, safely and effectively cleans all metal, concrete, rubber, and plastic surfaces.
VERSATILE CLEANER It may be used as a stripper for removing old wax because it contains special rust inhibitors for cleaning metal surfaces.
ECONOMICAL May be diluted with 1‒15 parts of water for dependable cleaning power and costs pennies per gallon. It may be sprayed or mopped onto surface reducing cleaning cost by eliminating waste and saving costly man-hours. It helps prolong the life of surfaces and equipment.
LEAVES NO FILM It cleans and removes residue and leaves a clean, bright surface that doesn’t leave an oily film.
NON-TOXIC Contains no carbon tetrachloride, naphtha, benzene, kerosene, gasoline, or other hazardous solvents that produce toxic fumes. Safe to use in commercial kitchens and food-storage facilities. 
100% FIREPROOF Will not burn or support combustion. It is fireproof and does not give off dangerous toxic fumes. Use safely inside or outside.

DIRECTIONS

Make a test panel before general cleaning. Protect and test all non-intended surfaces.

GENERAL CLEANING

  • Spray Bio-Dissolve with Enzymes cleaner on the stain/spot and affected areas.
  • Wait 15‒20 seconds and scrub the stain/spot gently with a very soft nylon brush, then rinse.
  • If the stain/spot remains, repeat the above steps until the stain/spot disappears. 

FOR EXTERIOR CLEANING

  • Prewet surface.
  • Dilute Bio-Dissolve with 4‒6 parts water. Determine the dilution from prior testing.
  • Apply diluted cleaner onto the surface with a soft nylon-fibered brush.
  • Let set for 2‒3 minutes. Do not let cleaning solution dry on the surface. 
  • Rinse off with water or pressure washing equipment (3 gallons per minute at 400‒600 psi). To avoid streaking, keep lower area wet at all times. 

Nanotized Biological Canvas, Fabric and Vinyl Cleaner and Stain Remover

Bio Safe-CFV is formulated with most the advanced Nano technology combined and fused with ecofriendly biotechnology—no harmful acids, solvents, or phosphates. Nano molecules penetrate rapidly into surface stains followed by a biological cleaning agent that dissolves, lifts, and removes stains instantly without harming the surface. It is especially designed for awnings, tents, and outdoor canvas, and fabric- and vinyl-type material and signs. Bio Safe-CFV rapidly cleans and removes biological and air pollution stains left behind by, withering, mold, algae, moss, mildew, and lichens and preserves and protects surfaces from further staining. 

Application Process

Always spot test product first to determine coverage, contact and cleaning time.

  • Apply Bio Safe-CFV with a brush, roller, hand pump sprayer (garden style pump sprayer), or low pressure power sprayer.
  • Prewet surface with water first then apply Bio Safe-CFV. Dilution not required; use as is.
  • For cleaning heavy mold and mildew staining, presoak material before scrubbing and rinsing.
  • Allow product to remain on the surface for 10‒12 minutes.
  • Scrub with soft nylon or natural bristle brush. DO NOT USE metal brush as it can scratch or damage the surface.
  • Rinse with clean water and continue to scrub and rinse until stain is removed.
  • Use low pressure washer to clean and rinse large areas; adjust pressure based on the surface to avoid surface damage. Spot test and adjust pressure before rinsing entire area.
  • If some stains appear after rinsing, repeat above steps and rinse thoroughly.
  • Use this product above ambient air temperature (45°F) for maximum cleaning performance. For heavy growth and deposits, use plastic scrapers and tools to loosen and scrape the surface. Keep surface wet with water.
  • Protect all surrounding surfaces which are not to be cleaned from overspray and prevent excessive plant and ground exposure. Rinse all oversprayed surfaces with plenty of water.

No Scrub/No Rinse Method

  • Using a sprayer (pump-up, low-pressure, or garden hose), apply and wet the entire surface with Bio Safe-CFV. Allow to air dry. 
  • Bio Safe-CFV works with the elements and results occur in less than one hour, depending on severity of staining. Reapply if stain persists.

Annual Maintenance Program 

For regular maintenance after initial cleaning, a light, yearly spray application of Bio Safe-CFV will help maintain a clean, stain-free surface. If heavy mold or mildew staining occurs, use and follow cleaning steps described in application process.

  • Brick Clean 101 has user-friendly synthetic acid chemistry that replaces muriatic and hydrochloric acid, making the acid easier to use. Brick Clean 101 offers the advantages of powerful acids while significantly improving the overall health and safety risk profile.

    BENEFITS & FEATURES

    • For removing excess mortar from dark and light colored brick.
    • Economical – designed for dilution
    • Will not cause burns on masonry.
    • Easier to handle and use.

    Note: for white, buff (low density), magnesium, pink salmon, use EST’s Brick Clean – Vanadium. As with new brick masonry prone to vanadium (green stain), manganese (dark brown), and other metallic stains. 

    DIRECTIONS

    DILUTION

    Masonry Type Brick Clean (v/v) Water (v/v)
    Brick Red, high-density, etc. 1 5
    Brick-buff (Not discoloration prone) 1 5
    Light-Colored Brick 1 5
    Structural, glazed, ceramic or mosaic Tile 1 8

    Always make test panel before general cleaning. 

    Protect and test all non-masonry surfaces.

    Coverage will average 400 sq. ft. per gallon.

    Prepare area: Removes job-dirt, mud stains, excess mortar from brick masonry, stone, structural tile, and exposed aggregate concrete surfaces.  It is safe for aluminum windows and trim. 

    EXTERIOR CLEANING

    • Pre-wet masonry thoroughly.
    • Dilute Brick Clean 101 with water, determine effective dilution from prior testing.
    • Apply Brick Clean 101 with masonry brush.
    • Let set for 2–3 minutes. Scrap excess mortar off (do not let cleaning solution dry on masonry surface.
    • Rinse off with water for pressure washer equipment (3 gallons per min at 400–600 PSI)
      Keep lower surface wet at all times to avoid streaking.

    INTERIOR CLEANING:

    Provide adequate ventilation.  Protect floor with poly film or other method.  Protect plumbing fixtures, doorknobs, light fixtures, etc.  Follow above procedure. If water hose cannot be used, use sponge or brush for rinsing.  Thorough rinsing is a must. Use 2 ounces of household ammonia to 2 gallons of water for rinse to neutralize where adequate rinsing is not possible.

    STORAGE AND HANDLING

    Note: Follow directions carefully. Always consult your dealer or supplier for timing, methods and to customize application, depending on contaminations.

    Keep product away from skin and eyes. Do not swallow or ingest this product. The use of rubber, neoprene, nitrile or other protective gloves is required where prolonged or extensive use is expected. Remove contaminated clothing and DO NOT wear again until thoroughly cleaned. Wash hands thoroughly with soap and water after handling. 

    Keep container closed when not in use. Store out of direct sunlight. Keep from Freezing. Avoid temperatures above 100 °F, or below 40 °F.

    CONDITIONS OF SALE

    Always follow all label directions. The manufacturer cannot control weather conditions, methods of application nor the condition of the area at time of application. Buyer assumes all risks of use, storage or handling of this product when used in a manner inconsistent with label directions. EST Inc. will not be responsible for any injury, loss, or damage if product is used or stored in any manner not in compliance with label/tech sheet directions or if precautions are not observed.

    First Aid 

    KEEP OUT OF REACH OF CHILDREN AND AWAY FROM PETS. 

    STORE AWAY FROM FOOD AND DRINK.

    EYES: Immediately flush eyes with plenty of water and continue for at least 15 minutes, occasionally lifting the upper and lower eyelids. Get medical attention if irritation persists.

    SKIN: Flush affected areas with plenty of water. Get medical attention if irritation persists.

    INGESTION: If this product is swallowed, do not induce vomiting. If vomiting occurs, keep head below hips to prevent aspiration (breathing) of liquid into lungs. Get medical attention immediately.

PRODUCT DESCRIPTION

Citra Strip WB is a biodegradable, VOC-compliant, non-solvent-based a carpet adhesive and mastic remover. It is designed to remove adhesives, oil, grease, enamel- and latex-based paint, and lubricants and other petroleum-based coatings and residues. Citra Strip WB is a safe alternative to hazardous terpene and hydrocarbon-based-chlorinated solvents.

FEATURES

      • VOC-compliant.
      • Non-flammable.
      • Non-corrosive.
      • Biodegradable.
      • Indoor/outdoor use.
      • Very low odor.
      • Easy clean up with water.
      • Easy to use, no dilution necessary.

DIRECTIONS

PRECAUTIONS: For industrial/professional use only. Protect all surroundings such as glass, wood, metal, plastic, floors, shrubs, and all non-cleaning surfaces. If over sprayed, wipe off immediately. This product is not recommended for use on wood floor surfaces, like plywood, composite or particle board and all other types of wood surfaces. Long-term exposure may cause wood surface to dwarf or buckle. Do not dilute or alter this product with other solvents or cleaners; it is made to use as is.

APPLICATION: Apply Citra Strip WB directly to the surface to be cleaned.

Apply on the surface by pouring, spraying (with low-pressure sprayer), brushing or soaking parts in the cleaner, letting soak for five to ten minutes before scraping. If residue becomes extremely thick, reapply and scrape softened material away until base surface is visible. If residue still remains, apply second coat, wait a few minutes, then scrape off final residue. 

Wash floor with EST Inc.’s Heavy Duty Cleaner by mopping and rinsing with water to ensure a clean surface. Allow surface to dry thoroughly.

Concrete Equipment Cleaner is specially designed to clean off dry mud and concrete from scaffolding, cement mixing trucks, and other concrete handling equipment. Without affecting the underlining surfaces. Concrete Equipment Cleaner contain a user-friendly synthetic acid chemistry that replaces muriatic and hydrochloric acid, making the acid easier to use. This product offers the advantages of powerful acids while significantly improving the overall health and safety risk profile.

Applications

Exterior Cleaning: Prewet the surface. Dilute some of the concentrate with 2–6 parts of water; determine the dilution from prior testing. (In some cases, concentrated product may be used.) Apply diluted concrete cleaner with a soft-fibered masonry brush. Let stand 2–3 minutes; reapply. Do not let the cleaning solution dry on the surface of the equipment; rinse off with water using pressure washing equipment (3 gallons per minute at 400–600 psi).

Interior Cleaning: Provide adequate ventilation. Protect the floor with poly film or other protection. Follow the procedures for exterior cleaning. If a water pressure machine cannot be used, use a sponge or brush for rinsing; thorough rinsing is a must.

PRODUCT DESCRIPTION

E-Cure 101 is a powder additive made expressly for use in cement products where efflorescence, calcium, or water-hardness , is a problem. E-Cure 101 prevents and binds chlorides, salts, and minerals at the Nano-molecular level. E-Cure 101 is specially formulated for cement and mortar mixers. This keeps efflorescence, calcium, and water-hardness from permanently leaching out onto brick, block, and other mortar-set products; it is also excellent for pre-cast and poured-in-place concrete.

Note: EST Inc. can also furnish a clear, UV-positive sealer in matte, semi-gloss, or gloss finish for new construction of clay or cementations surfaces that waterproofs and protects against color bleaching.

COMPOSITION

E-Cure 101 is a proprietary mix solution containing glyolatetrigcatate Nano composites in aqueous solutions that react with impurities such as calcium and mineral-based salts found in mortar mixes, cement products, and aggregates. This reaction permanently binds these impurities within these substrates and prevents efflorescence salt from leaching out to the surface.

Recommended Substrates

Brick, block, stone, stucco, tiles, poured in place, pre-cast, and any other cementations product.

ADVANTAGES

  • Provides an excellent water and moisture screen.
  • Cures efflorescence permanently.
  • Stabilizes and brightens integral colors in concrete blocks, roof tiles, pavers etc.
  • Units made with E-Cure 101 can be painted or sealed.
  • Can be used with plasticizers.
  • Extends set time resulting in greater strength.
  • Helps increase density and cure strength.
  • VOC-compliant with water cleanup.

 

GENERAL DOSAGE USE CHART
Per lbs. of Sand and Cement Mix E-Cure 101
100 lbs./mix 4–6 oz
200 lbs./mix 8–12 oz
300 lbs./mix 12–18 oz
400 lbs./mix 16–24 oz
500 lbs./mix 20–30 oz

 

Note: Above chart is for normal standard mix only. If your mix has problem with efflorescence please do sample cube test (pretest) and adjust dosage according to that. E-Cure 101 can be used up to 8‒10 oz per 100 lbs. of mix. Follow mix ratio as recommended below.

E-Cure 101 Additive (cont.)

 

MIX RATIOS
Sand/Cement Ratio E-Cure/100/lbs. of Cement
3:1 4–8 oz
4:1 5–10 oz
5:1 6–12 oz

 

Note: Mix ratios are approximates and may vary due to mix design and aggregates used. A pre-test of samples is recommended. Contact EST Inc. for assistance if problems occur in reaching optimum mix ratios or where unusual applications are involved. Our technical department is dedicated to finding solutions to efflorescence in other concrete applications or installation problems.

PRECAUTION

Do not mix any other companies’ products or additives. Mix with only EST Inc. supplied products and additives. Add them separately in sequence if needed, allow minimum of five minutes mixing time per each sequence. For general practice we do not recommend mixing plasticizer and E-Cure 101 together before adding to the batch.

Mix sequence options

  • Sand, cement, color, water, plasticizer, E-Cure 101.
  • Mix Water, E-Cure 101, plasticizer together, then add to sand cement and color.
  • Sand, cement, color, water, E-Cure 101, then plasticizer.
ASTM TEST DATA
ASTM C-33 Normal weight aggregates
ASTM C-150 For Portland cement
ASTM C-55 Grade N concrete brick
ASTM C-145 Grade N solid load bearing unit
ASTM C-90 Grade N Hollow load-bearing unit

LIMITATIONS

Prevent from freezing. Patch test recommended assuring proper mix ratios.

Enviro Seal 227-T is a water-based, Nano- alkylalkoxysilane-penetrating, water repellent. It is designed specifically for brick, masonry, limestone, sandstone, pre-cast and concrete surfaces including blocks, pavers, stucco, and many natural surfaces where darkening is unacceptable. Dries clear and tack free.

Enviro Seal 227-T reduces bonding of airborne hydrocarbons, reduces water damage, freeze-thaw from snow and ice, repels water, protects surfaces against efflorescence, and has excellent ultraviolet resistance. It is VOC (Volatile Organic Compound) compliant as well.

APPLICATIONS

  • Protect all non-masonry surfaces.
  • Treated surface should be free of dirt, grease, moisture, etc.
  • New concrete should be allowed to cure at least 14 days before application.
  • Product may be applied with low-pressure spray equipment, a brush, or a roller.
  • When using low-pressure equipment, apply a light mist coating to break the surface tension; this allows for good penetration. Repeat the process with flood coat (4‒6 inches run down).
  • Drying times will depend on temperature and humidity.
  • 8–12 hours for initial cure, with additional curing happening over 24–48 hours.

Note:

  • Air and surface temperature must be above 40°F during application.
  • Caulking should be installed prior to application.
  • Protect surrounding non-masonry surfaces, such as glass, aluminum, etc.
  • Inadvertent splash should be removed with water before the solution has dried on the surface.
  • Do not apply when rain is predicted with 24 hours.

COVERAGE (Approx.)

Brick Masonry 150–200 sq ft/gal
Limestone (Smooth) 100‒150 sq ft/gal
Limestone (Rough) 100‒125 sq ft/gal
Smooth (Precast) 100‒125 sq ft/gal
Rough Exposed Aggregate 80‒125 sq ft/gal
Block (High Density) 75‒100 sq ft/gal
Block (Low Density) 50‒75 sq ft/gal
Natural Stone 100–125 sq ft/gal

Fast Act-130 Low-Odor Mastic Remover is a specially-formulated product designed to remove all types of adhesives, paint, magic marker, lipstick, scotch tape, light coatings, and mastic from concrete and wood surfaces.

PHYSICAL DATA

Boiling point 360°F
Percent Volatile 96%
Freezing Point N/A
Solubility in H2O Emulsifiable
Appearance/Odor Light Red/Citrus
pH Neutral

Directions

Apply Fast Act-130 Low-Odor Mastic Remover directly onto the surface using a spray, brush, or cloth; the surface must be dry before applying. Let set for 2–3 minutes; reapply lightly and rinse it off with maximum water pressure or wipe it off with a cloth. (Use a scrapper or auto-scrubber with black pad to scrape off excess build-up.) Reapply Fast Act-130 Low-Odor Mastic Remover and then wipe it off again until the surface becomes clean. For heavily defaced areas, a second application may be necessary.

Graffiti-Off paint remover is an effective, biodegradable, water-based formula that attacks paint so it can be easily be sprayed or wiped away. Graffiti-Off is safe for the environment. It works more effectively—or better—than most solvents in the same time and costs less per ounce. 

This formula actually breaks the molecular bond between the paint and the substrate surface and is effective for removing graffiti from all types of surfaces including: stucco, concrete, trucks, and street signs. It provides superior performance on the most porous of surfaces such as natural brick and concrete.

Graffiti-Off is the first real alternative to anti-graffiti coatings and the continued painting over of graffiti. 

It comes in a handy, ready-to-use, 32-oz spray bottle.

Application Surfaces:

Soft, Porous and hard

  • Brick.
  • Concrete.
  • Stone.
  • Stucco.
  • Rock.
  • Tile.
  • Fiberglass.
  • Aluminum.
  • Alloy.
  • Stainless steel.
  • Metal street signs.
  • Formica.
  • Plastic.
  • Plexiglas.

BEFORE CLEANING

Test surfaces before using. Apply a small amount to an inconspicuous area.

DO NOT USE if surface marks, dulls, discolors, fades or if color transfers to a white cloth. Not recommended for used on faded or varnished surfaces, non-colorfast materials or woodwork.

DIRECTIONS 

POROUS SURFACES (BRICK, CONCRETE & STUCCO)

  1. Spray affected area, wait 3‒5 minutes. 
  2. Use brush to loosen dried paint. 
  3. Use hose to rinse off and wipe with a clean towel. 

For best results on porous problem graffiti areas, use a high-pressure spray washer after – step #1.

HARD and SOFT SURFACES (STREET SIGNS, TILE, ETC.)

Spray stain thoroughly, wait 60 seconds. Wipe with clean disposable towel or cloth. Repeat if necessary.

Heavy-Duty Concrete Cleaner removes dirt, rust, retarders, and mud stains from tough finishes. It is ideal for older concrete cleaning and etching and it could be used on colored concrete and most anodized aluminum and is great for rough form finishes, sand-blasted surfaces, heavily-textured surfaces, exposed aggregate (aggregate exposure), and concrete block.

ADVANTAGES

  • Corrects color and texture irregularities.
  • Economical.
  • Removes Oil, Grease and Stains from Concrete.
  • Removes smoke, rust, and efflorescence.

DIRECTIONS

Make a test panel before general cleaning. Protect and test all non-masonry surfaces.

EXTERIOR CLEANING

  • Prewet surface.
  • Apply diluted cleaner onto the surface with an air-less spray pump. 
  • Scrub surface with a soft, fibered masonry nylon brush.
  • Let set for 2‒3 minutes. Do not let cleaning solution dry on the concrete. 
  • Rinse off with water or pressure washing equipment (3 gallons per minute at 400‒600 psi). Always use caution when using pressure, take care to not damage the underlying surface. To avoid streaking, keep lower area wet at all times.
  • Repeat above steps until stains are removed.

INTERIOR CLEANING

  • Provide adequate ventilation for air circulation.
  • Protect floor with poly film or another appropriate method. Protect plumbing fixtures, doorknobs, light fixtures, etc. 
  • Follow the procedures above (exterior cleaning). If a water hose cannot be used, use a sponge or brush for rinsing. Thorough rinsing is a must.

Note: Use EST’s Light-Duty Concrete Cleaner for smooth white, gray, and colored architectural concrete.

DILUTION
Substrate HD Concrete Cleaner Water
Exposed Aggregate (general cleaning)  1 part 6 parts
Exposed Aggregate (aggregate exposure) 1 part 2 parts
Form Finished Concrete (smooth and rough texture)  1 part 6 parts
Concrete Block (weathering or etching) 1 part 2 parts
Concrete Block (removal of mortar stains, etc.)  1 part 6 parts

ACID-FREE, ECONOMICAL, and ENVIRONMENTALLY-SAFE 

PRODUCT DESCRIPTION

This powerful cleaner is a balanced chemical compound. Its minimum foaming properties allow free rinsing and contains no hydrocarbons or other chlorinated solvents. It is effective in dissolving heavy deposits of oxidized waxes and polymers, thick layers of downtrodden greases, and baked-on deposits of carbon, fire-damaged hard surface deposits, soot, resins, gums, oils, inks, dyes, and hard soap scum.

 

Recommended surfaces

  • Fire-, smoke-, & flood-damaged surfaces.
  • Brick, concrete, and masonry.
  • Aluminum and vinyl siding.
  • Glass and Plexiglas surfaces.
  • Paved stone, flag stone, and precast concrete surfaces.
  • Aluminum and most metallic surfaces.
Features

  • Provides safe handling.
  • Environmentally-safe.
  • No acid burning or acid fumes.
  • Does not damage any kind of masonry surfaces.
  • Excellent for general job site cleaning.
Technical Data

Form Liquid
Flash Point None
pH 10
Weight/Gal 8.7 lb/gal
Color Light Red
Biodegradable Yes
Shelf Life 1 year

HD Paint & Epoxy Stripper Gel is a specially formulated product to remove all types of coatings, paint, epoxies, decals, adhesives, Scotch-Lite coatings, etc. For all exterior applications.

Directions

Do not dilute or alter packaged material.

REMOVES

Paint and Epoxy coatings from metal, concrete, wood, fiberglass, and stone & ceramic tiles.

Always try product on a test panel to adjust rates and times.

  • Apply HD Paint & Epoxy Stripper Gel liberally on the surface to be cleaned. 
  • Use natural-bristle brush only. 
  • Do not use rubber or plastic bucket or tank as holding tank.
  • Allow HD Paint & Epoxy Stripper Gel to stand until coating or decal starts to wrinkle.
  • Dwell time will depend on the cleaning target and on its thickness.
  • Lift coating or decal with a putty knife or by scrubbing. For stubborn spots, agitate with steel wool or wire brush.
  • Rinse area with a detergent solution.
  • Use scrubbing pad to remove hidden residue from cracks, joints, and dings from the floor.
  • For difficult removal, above procedures may be repeated.

NANOTIZED BIOLOGICAL MULTI-SURFACE CLEANER & RESTORER

Designed for Asphalt, Concrete, Metal & wood Roofs

Heavy-Duty Roof Cleaner–ACMW is formulated with most advanced nanotechnology combined and fused with eco-friendly biotechnology containing no harmful acids, solvents, or phosphates. Nano-molecules penetrate rapidly into surface stains followed by a biological cleaning agent that dissolves, lifts, and removes stains instantly without harming the surface.

·       Weathering Stains ·       Other Stubborn Soils
·       Pollution Stains ·       Leaf Stains
·       Graying Stains ·       Most Organic Stains
  • DEEP CLEANS
    It contains a deep penetrating emulsifier that penetrates and floats away even the most stubborn stains and soils.
  • WATER SOLUBLE
    Powerful—mixes with water for fast, safe cleaning action.
  • EASY-TO-USE
    Can be mopped, sprayed, or wiped on metals, plastic, rubber, and concrete. It goes to work immediately— absorbs, emulsifies, and floats soil away and helps prolong the life of surfaces and equipment.
  • NON-TOXIC
    Heavy-Duty Roof Cleaner–ACMW is water-based, VOC compliant and bio-degradable. Contains no carbon tetrachloride, naphtha, benzene, kerosene, gasoline, or other hazardous solvents that produce toxic fumes.

Surface Applications

Heavy-Duty Roof Cleaner–ACMW rapidly cleans and removes harmful biological and air pollution stains that are left behind by mold, algae, moss, mildew, and lichens on many building materials such as concrete, brick, masonry, limestone, sandstone, brown and natural stone, terracotta, travertine, stucco, marble, granite. For roofs made with metal, wood, concrete and asphalt.

Directions

Always spot test product first to determine coverage, contact, and cleaning time.

  • Apply Heavy-Duty Roof Cleaner–ACMW with a brush, roller, hand pump sprayer (garden style pump sprayer), or low pressure power sprayer.
  • May also be used in soft washing for more sensitive surfaces.
  • Prewet surface with water first then apply undiluted product. Dilution not required; use as is.
  • Allow product to remain on the surface for 10‒12 minutes.
  • Scrub with soft nylon or natural bristle brush. Do Not Use metal brush as it can scratch or damage the surface.
  • Rinse with clean water and continue to scrub and rinse until stain is removed.
  • Use low pressure washer to clean and rinse large areas; adjust pressure based on the surface to avoid damage to the surface. Spot test and adjust pressure before rinsing entire area.
  • If some stains appear after rinsing repeat above steps and rinse thoroughly.
  • Use this product above ambient air temperature 45°F for maximum cleaning performance.
  • For heavy buildup and deposits use plastic scrapers and tools to loosen and scrape the surface. Keep surface wet with water.
  • Protect all surrounding non-cleaned surfaces from overspray and prevent excessive plant and ground exposure. Rinse all over-sprayed surfaces with plenty of water.

NO SCRUB/NO RINSE METHOD

  • Using a sprayer (pump-up, low pressure, or garden hose), apply and wet the entire surface with Heavy-Duty Roof Cleaner–ACMW. Allow to air dry.
  • Heavy-Duty Roof Cleaner–ACMW works with the elements and results occur within one week to one month, depending on severity of staining. Reapply if stain persists or rain occurs within 12 hours of application.

Annual Maintenance Program

Preserve and protect surfaces from detraction and staining. For regular maintenance after initial treatment of substrate, a once-a-year light spraying application of Heavy-Duty Roof Cleaner–ACMW will help maintain a clean, stain-free surface. If heavy growth or staining occurs, use and follow cleaning steps described in application process.

AFTER CLEANING

  • Use EST Inc.’s Nano Seal Fusion-CFW, Aqua Silane 40, or Enviro Seal 227T (Nano-Enhanced) to seal, and protect the surface, to prevent the cleaned surface from weathering and aging stains.

Heavy Duty Rust Remover – Liquid Gel removes rust from all metal, fiberglass, masonry, and concrete surfaces. It is Eco-Friendly, biodegradable and does not contain animal fat or solvents. Rinses free of residue. Contains Acid-Free Nano Technology and surfactants.

APPLICATION

PRECAUTION

Protect all non-targeted surfaces and surrounding areas from overspray when cleaning and rinsing.

Apply on hard surfaces with paintbrush or roller where rust stains and loose rust are present. Wait 3–5 minutes then wash surface with water. Repeat application if necessary, until rust stains are removed.

HARD TO REMOVE STAINS

Pre-wet surface with water before applying stain remove; wait 3–5 minutes then scrub with nylon brush and follow up with high-pressure rinse. Repeat the same application if necessary, until rust stain is removed. Use plenty of water to rinse surface thoroughly. Do not let rinse water puddle on any nearby clean surface. Keep surface wet and rinse water away from clean areas.

Cleaning polished surfaces

Test panel is recommended when cleaning polished, glazed, and smooth surfaces. Prolonged use of this product can remove shine and glaze from the surface. Always test small area first to determine cleaning time, result and effectiveness of this product.

Heavy Duty Wood Cleaner Nano-Enhanced is a versatile and safe cleaner; it cleans effectively all wooden surfaces, thoroughly removing stains left behind by weathering and pollution.

Use for wood decks, fencing, roofing, wood-shake shingles, benches, chairs, furniture, wooden siding, exterior wood surfaces, and more. Safe to use on pinewood, redwood, cedarwood, CCA-Treated wood, and most natural wood surfaces. 

ADVANTAGES

REMOVES

  • Weathering Stains
  • Other Stubborn Soils
  • Pollution Stains
  • Leaf Stains
  • Greying Stains
  • Most Organic Stains
  • DEEP CLEANS
    It contains a deep penetrating emulsifier that penetrates and floats away even the most stubborn grease and soils.
  • WATER SOLUBLE
    Powerful—mixes with water for fast, safe cleaning action.
  • 100% FIREPROOF
    Will not burn or support combustion and does not give off dangerous toxic fumes; use safely inside or outside.
  • EASY-TO-USE
    Can be mopped, sprayed, or wiped on metals, plastic, rubber, and concrete. It goes to work immediately— absorbs, emulsifies, and floats soil away and helps prolong the life of surfaces and equipment.
  • NON-TOXIC
    Contains no carbon tetrachloride, naphtha, benzene, kerosene, gasoline, or other hazardous solvents that produce toxic fumes.

DIRECTIONS

Protect and cover all non-intended surfaces with plastic drop-cloth or trap from overspray, including glass, windows, and siding. Make a test panel before general cleaning.

GENERAL CLEANING

  • Spray HD Wood Cleaner on the stain/spot and affected areas.
  • Wait 30‒60 seconds and scrub the stain/spot gently with a very soft nylon brush, then rinse.
  • If the stain/spot remains, repeat the above steps until the stain/spot disappears.

FOR EXTERIOR CLEANING

  • Prewet surface.
  • Dilute HD Wood Cleaner with 4‒6 parts water. Determine the dilution from prior testing.
  • Apply diluted cleaner onto the surface with an air-less spray pump. 
  • Scrub surface with a soft nylon-fibered brush.
  • Let set for 2‒3 minutes. Do not let cleaning solution dry on the surface. 
  • Rinse off with water or pressure washing equipment (3 gallons per minute at 400‒600 psi). Always use caution when using pressure, take care to not damage the underlying surface. To avoid streaking, always keep lower area wet.

AFTER CLEANING

  • Use EST Inc.’s Wood Pro – Wood Sealer to prevent the cleaned surface from weathering and aging stains.

STORAGE AND HANDLING

Keep product away from skin and eyes. Do not swallow or ingest this product. The use of rubber, neoprene, nitrile or other protective gloves is required where prolonged or extensive use is expected. Remove contaminated clothing and DO NOT wear again until thoroughly cleaned. Wash hands thoroughly with soap and water after handling. 

Keep container closed when not in use. Store out of direct sunlight. Keep from Freezing. Avoid temperatures above 100 °F, or below 40 °F. Product can be stored up to 12 months. If product is stored for a long time, lightly agitate or shake well before use. This product is biodegradable and eco-friendly.

 Note: Follow directions carefully. Always consult your dealer or supplier for timing, methods and to customize application, depending on contaminations.

Hydra Cure and Seal WB (Water-Based) is a concrete curer and sealer. It is quickly and easily applied to cure, seal, and dust-proof new and old, interior and exterior, vertical and horizontal concrete surfaces. It retains 95% or more of the mix water in concrete for seven days allowing for normal hydration and will self-dissipate as concrete cures.

Hydra Cure and Seal can be made with a red fugitive dye to aid in application. Meets TYPE-1D requirements.

When properly applied, Hydra Cure and Seal produces an impermeable seal for efficient moisture retention. It is ideal for application on commercial and industrial floors, sidewalks, basements, garage floors, multi-level parking decks, patios, driveways, and parking areas.

ADVANTAGES

Hydra Cure and Seal significantly reduces blushing. It provides an excellent thicker, long-lasting film finish that is resistant to most chemicals, petroleum, and abrasives. When properly applied, Hydra Cure and Seal yields superior curing efficiency; hairline cracks, premature cracking, and dusting, and spalling are all prevented with good concreting practices. Hydra Cure and Seal is not a cure-all for improperly mixed or placed concrete. Hydra Cure and Seal is VOC (Volatile Organic Compound) compliant, with a maximum VOC content of > 28.

SPECIFICATIONS

ASTM – C 309, Type 1, class B.

ASTM – C 1315.

AASHTO M-148, Type 1, class B

Federal specification TT-C-0800.

USDA accepted.

VOC > 28 gm/ liter.

COVERAGE*
Curing and for moisture retention. 200–300 ft2/gal (4.9–9.8m2/L)
Second Coat 400–800 ft2/gal (9.8 –14.7m2/L) 

(dust proofing and sealing)

Renovating, dust proofing and sealing 200–300  ft2/gal (4.9–7.4m2/L)
Under mastic-type floor adhesives 400–600 ft2/gal (9.8 –14.7 m2/L)

*Coverage varies with application method, texture and porosity of surface.

APPLICATION

Hydra Cure and Seal is ready to use as is. Use a commercial sprayer for efficient application; a nap roller, soft bristle broom, or a lamb’s wool applicator may also be used. The sealer should be sprayed-on with an 8001 tip in a fine-fog pattern without spurts and dribbles, forming a thin continuous film.

Avoid creating puddles in low areas. If puddles occur, brush or roll them out.

Hydra Cure and Seal appears “milky white” in the container and has a “bluish cast” when applied for easy identification of coverage. It dries clear to provide a transparent sheen finish; Hydra Cure and Seal will not change the color of the concrete.

Concrete Equipment Cleaner is specially designed to clean off dry mud and concrete from scaffolding, cement mixing trucks, and other concrete handling equipment. Without affecting the underlining surfaces. Concrete Equipment Cleaner contain a user-friendly synthetic acid chemistry that replaces muriatic and hydrochloric acid, making the acid easier to use. This product offers the advantages of powerful acids while significantly improving the overall health and safety risk profile.

Applications

Exterior Cleaning: Prewet the surface. Dilute some of the concentrate with 2–6 parts of water; determine the dilution from prior testing. (In some cases, concentrated product may be used.) Apply diluted concrete cleaner with a soft-fibered masonry brush. Let stand 2–3 minutes; reapply. Do not let the cleaning solution dry on the surface of the equipment; rinse off with water using pressure washing equipment (3 gallons per minute at 400–600 psi).

Interior Cleaning: Provide adequate ventilation. Protect the floor with poly film or other protection. Follow the procedures for exterior cleaning. If a water pressure machine cannot be used, use a sponge or brush for rinsing; thorough rinsing is a must.

Lift-Off Epoxy & Polyurethane Coating Stripper is biodegradable and extremely strong stripper that effectively removes most clear and pigmented epoxy and polyurethane, coatings from hard surfaces. It is safe to use on wood, metal, concrete, fiberglass, ceramic, VCT, stone tiles and various masonry surfaces, from floors and walls. Does not contain methylene chloride or other solvents, it is non-flammable and exceptionally low to no odor, designed for all interior and exterior applications.

Features

  • Low V.O.C. 
  • Cleans up with water
  • Low to No odor
  • Easy to use and apply
  • Non-methylene chloride & solvent free formula
  • Nano-Enhanced for quick penetration and stripping action.
  • Non-reactive will not generate odor or off gassing.

Benefits

  • Use on all epoxy and polyurethane coated hard surfaces  
  • Safe to use on metal, wood, tiles, fiberglass, concrete, and masonry surfaces
  • Removes clear and colored epoxy and urethane coatings 
  • Strips multiple layers safely and effectively
  • Can be use with auto scrubber with black pad for quick stripping
  • Ready-to use formula works much faster than most epoxy strippers

Application and Directions

Do not dilute or alter packaged material.

Always try product on a test panel to adjust rates and times.

  • Apply Lift-Off Stripper liberally on the surface to be cleaned. 
  • Dwell time will depend on the cleaning target and on its mil thickness, approximate time between 1–6 hours.
  • Use natural-bristle brush, spray, or roller for even application
  • Allow Lift-Off Stripper to stand on the surface until coating starts to wrinkle or begins to look dry and turn powdery.
  • Lift coating with a wide putty knife or by scrubbing. For stubborn spots, agitate with scrubbing pad or hard bristle brush.
  • Use small hard bristle brush to remove material from grout joints.
  • For difficult removal, and multi-layer epoxy coating, above procedures may be repeated.
  • Rinse area with water, mop and squeegee or use wet vacuum to pick up excess wetness.
  • Use EST Inc.’s Neutral Cleaner product to neutralize floor surface pH close to 7, before applying any types of floor wax or finish.

 

Helpful Tips: If Lift-Off stripper puddles and gather around lower area, spread out the stripper evenly away from the low area. For stripping floor surfaces-apply only small area at a time for better control and workability. Dwelling time may depend on the mil thickness of the epoxy coating. Standard dwelling time from contact to strip is normally between 1 to 6 hours depending on the surface temperature.

Cleanup and Disposal

Collect all stripped epoxy (hard and soft gunk) material into a plastic container for proper disposal. Rinse and mop floor with water. If necessary, use scrubbing pad to remove hidden residue from cracks, joints, and dings from the floor. Follow up with neutral cleaner mop and rinse. Let floor dry completely before applying any type of new coating.

Light Duty Concrete Cleaner Concentrate removes dirt, rust, weathering and pollution stains. It is ideal for smooth white, gray, and colored architectural concrete, and masonry, marble, and tile floors.

ADVANTAGES

  • Can be used indoors and outdoors and has no harmful fumes.
  • It will not etch concrete.

APPLICATION

Make a test panel before general cleaning. Protect and test all non-masonry surfaces.

Dilution: 1 part cleaner to 1 or 2 parts water.

Exterior Cleaning

  • Prewet surface.
  • Apply diluted cleaner onto the surface with an air-less spray pump. 
  • Scrub surface with a soft, fibered masonry nylon brush.
  • Let set for 2‒3 minutes. Do not let cleaning solution dry on the concrete. 
  • Rinse off with water or pressure washing equipment (3 gallons per minute at 400‒600 psi). Always use caution when using pressure, take care to not damage the underlying surface. To avoid streaking, keep lower area wet at all times.
  • Repeat above steps until stains are removed.

Interior Cleaning

  • Provide adequate ventilation for air circulation.
  • Protect floor with poly film or another appropriate method. Protect plumbing fixtures, doorknobs, light fixtures, etc. 
  • Follow the procedures above (exterior cleaning). If a water hose cannot be used, use a sponge or brush for rinsing. Thorough rinsing is a must.

GENERAL SPOT CLEANING

  • Spray diluted Light-Duty Concrete Cleaner on the stain/spot and affected areas.
  • Wait 30‒60 seconds and scrub the stain/spot gently with a very soft nylon brush, then rinse.
  • If the stain/spot remains, repeat the above steps until the stain/spot disappears.

STORAGE AND HANDLING

Keep product away from skin and eyes. Do not swallow or ingest this product. The use of rubber, neoprene, nitrile or other protective gloves is required where prolonged or extensive use is expected. Remove contaminated clothing and DO NOT wear again until thoroughly cleaned. Wash hands thoroughly with soap and water after handling. 

Keep container closed when not in use. Store out of direct sunlight. Keep from Freezing. Avoid temperatures above 100 °F, or below 40 °F. Product can be stored up to 12 months. If product is stored for a long time, lightly agitate or shake well before use. This product is biodegradable and eco-friendly.

 Note: Follow directions carefully. Always consult your dealer or supplier for timing, methods and to customize application, depending on contaminations.

Nano Overcoat 2100DM is specially designed to protect dry mud and concrete from sticking to scaffolding, cement mixing trucks, and other concrete handling equipment. Without affecting the underlining surfaces

Nano Overcoat 2100DM is an invisible barrier designed for painted masonry surfaces, fiberglass and plastic panels, scaffolding, cement trucks, and other concrete handling equipment, and painted metal surfaces. NOT RECOMMENDED FOR WOOD SURFACES.

ADVANTAGES

  • Deep penetrating.
  • Forms a non-stick slick barrier.
  • Fills in micro-pores on the surface.
  • Repels dirt, dust, moisture, soap scum, concrete, mud, and stains.
  • Makes future surface cleaning easier and effortless.
  • Protects surface from discoloration and staining.
  • Saves labor and downtime

Application

Step 1

Before applying the Nano Overcoat 2100DM, use EST’s Heavy Duty Concrete Equipment Cleaner to clean the surface. This will remove any unwanted particles, dried concrete, mud, and stains. This will open the pores to allow the product to penetrate and adhere to the surface.

Note: Please consult the information on the EST’s Heavy Duty Concrete Equipment Cleaner container before using it.

Step 2

Apply the Nano Overcoat 2100DM with an airless sprayer; the surface should be clean and dry prior to application. If the surface is very porous, apply 1–2 coats if necessary, until the surface becomes saturated with the Nano Overcoat 2100DM. Allow 1–2 hours for the coating to penetrate and cure.

Coverage/Dilution

Use 5 gallons of concentrated Nano Overcoat 2100DM mixed with 25–30 gallons of water.

Approximate Coverage Rate: 700–1000 square feet per gallon based on porosity of surface.

Recommended Application

Based on the current condition of the surface, reapply as needed.

For preventative maintenance, reapply Nano Overcoat 2100DM each time each time after removing dried concrete-mud and stains from the surfaces.

PRODUCT DESCRIPTION

Nano Siloxane-100-2770 WB is a nonflammable, water-soluble, sodium methyl siloxane solution designed as a material additive or surface treatment to impart a water-repellent surface and reduce material water absorption. Supplied at a concentration of 30% solids in water, it is normally diluted to a concentration of 3% before being applied. The final concentration depends upon the application. The siloxane reacts with moisture and carbon dioxide in the air to form an insoluble water-resistant resin within 24 hours.

BENEFITS

  • Reduces water absorption into substrates.
  • Reduces spalling due to freeze-thaw and efflorescence.
  • Colorless and non-yellowing.
  • Preserves the natural appearance of substrate.
  • Penetrating, breathable, low VOC, and nonflammable.

APPLICATION

Nano Siloxane-100-2770 WB is a water-repellant treatment for application on plasterboard and plaster blocks.

PROPERTIES

Specification Writers: These values are not intended for use in preparing specifications. Please contact your local sales representative prior to writing specifications on this product.

Property Value
Composition Sodium Nano Methyl Siloxane
Color Clear to light yellow
Solids Content, after 90 min @ 65°C (150°F) 30%
Silicone Solids Content 19%
Specific Gravity at 25°C (77°F) 1.25
Flash Point, Open Cup >100°C (212°F)
pH 13
Density 10.4 lb/gal (1240 g/L)
Solvent (thinner) Water
VOC Content 0.668 lb/gal (80 g/L)

Directions

Surface Preparation

Surfaces to receive water-soluble siloxane should be lightly dampened immediately prior to application. Water-soluble siloxane does not wet a surface that has been previously treated with a water repellent. Do not use in a concentration higher than 3% solids unless prior testing indicates a necessity. The use of higher concentrations may result in the formulation of a white residue. Users should test any concentration on substrate prior to use.

Dilute Nano Siloxane-100-2770-WB to a concentration of 3% solids or less just prior to application. To prepare a 3% solution, mix one gallon (3.78 liters) of Nano Siloxane-100-2770-WB as supplied with 11 gallons (4.16 liters) of water.

After application of the solution, the treated surface should be allowed to dry at least 24 hours to develop maximum water repellency.

This interval may be shortened somewhat by force drying at temperatures up to 149°C (300°F). While this removes the water quickly, time must be allowed for the curing reaction between Nano Siloxane-100-2770-WB and the surface being treated; CO2 streams do not appear to reduce the cure time appreciably.

 

Substrate %Active Total Solids Coverage Rate ft2/gal (m2/I) %Water Exclusion vs. Control after 72 hrs2 %Water Absorption
Limestone 3 50 (1.2) 2.1 2.3
Control 6.0
Glen Gary 3 200 (4.9) 75.4 1.1
  Salem Brick Control 4.6
Belden Alamo 3 130 (3.2) 74.4 1.2
  Jumbo Brick Control 4.70
Belcrest 350 3 110 (2.7) 65.2 1.50
  Brick Control 4.50

PRODUCT SAFETY INFORMATION: See MSDS

USABLE LIFE/STORAGE

When stored at or below 25°C (77°F) in the original unopened containers, this product has a usable lifespan of 36 months from the date of production.

LIMITATIONS

This product is neither tested nor represented as suitable for medical or Pharmaceutical uses.

LIMITED WARRANTY

The information contained herein is offered in good faith and is believed to be accurate. However, because conditions and methods of use or our products are beyond our control, this information should not be used in substitution for consumer’s tests to ensure that our products are safe, effective, and fully satisfactory for the intended end use.

Suggestions of use shall not be taken as inducements to infringe any patent.

Your exclusive remedy for breach of such warranty is limited to refund of purchase price or replacement of any product shown to be other than as warranted.

Nano Seal Fusion-CFW is a non-toxic, environmentally-friendly product designed for use on unsealed concrete and wood and fiberglass (Artificial wood decking and fence) type surfaces. Its Nano-polymerized fusion particles adsorb deeply into the surface forming a flexible-polymer internal bond, becoming part of the wood, fiberglass and concrete structure. This enhanced structure resists water penetration effectively helping prevent corrosion, spalling, pitting, warping, and cracks. Nano Seal Fusion-CFW is resistant to freeze/thaw damage and helps protect the surface from deicing salts, rain, and pool chemicals while at the same time reducing the effects of stains from mold and mildew.

Basic Features

  • For all exterior wood and concrete surfaces.
  • Non-toxic, eco-friendly, and VOC-compliant.
  • Water & stain, resistant.
  • Prevents corrosion, spalling, and cracks.
  • Protects from deicing salt and pool chemicals. 
  • Resistant to freeze/thaw cycle.
  • Provides excellent chemical resistance and protection from oils, acids, chemicals, greases, solvents, and salts.
  • Exceeds ASTM Standards.

Directions

Surface should be free of all dust, debris, oil, and stains. Caulk all joints, repair any damage, wood rot areas and cracks and patch surfaces before applying. Use a low-pressure sprayer, roller, or brush for application. 

Mixing Instructions

Mix or shake gently prior to application. Gently mix for 3‒5 minutes. Do Not Mix Vigorously. (This can introduce air bubbles and foam.)

Old Concrete: Remove any tar, oil, and/or rust stains by using a high-pressure washer; use EST Inc.’s Heavy Duty Cleaner to remove stains.

New Concrete: The surface should be well-cured and kept moist using water, wet burlap, polyethylene, or curing paper. Membrane or chemical curing compounds should be removed by using a high-pressure washer and EST Inc.’s Heavy Duty Cleaner.

New Wood Surface: Remove any factory protective coatings before applying to the wood surface.

Old wood Surface: Clean all wood surfaces with EST Inc.’s Wood Cleaner before applying this product. Remove stains, mold, mildew, and repair if necessary, before applying this product.

New Fiberglass Surface: Remove any factory protective coatings before applying to the fiberglass surface.

Old Fiberglass Surface: Clean all fiberglass surfaces with EST Inc.’s  fiberglass Cleaner before applying this product. Remove stains, mold, mildew, and repair if necessary, before applying this product.

Vertical Surfaces: Application can be made with a low-pressure sprayer using 10‒20 psi or can be applied with a roller or brush. When spraying vertical surfaces, let the material run down 5‒15 inches, saturating the surface from the contact point; spray the surface again before the surface dries.

Horizontal Surfaces: Flood the surface using a low-pressure sprayer with 10‒20 psi, or use a roller, brush, or broom; apply evenly. Let the surface absorb the solution and follow-up immediately with a second application before the surface dries; redistribute any puddles or free standing material.

COVERAGE RATE/CURING TIME

Exact coverage will depend upon the porosity and density of the surface. Dry-to-touch in 2 hours; initial cure will take 16‒24 hours for light traffic. Maximum cure will require up to 7 days. 

CONCRETE ESTIMATED COVERAGE
(sq ft/gal)
Concrete (broom finish) 150‒200 
Concrete (smooth) 200‒250 
Stucco 100‒150 
Exposed Aggregate 100‒150 
Concrete Blocks 75‒100 
Brick Masonry 150‒200 
Pre-cast Horizontal 200‒250 
Pre-cast Vertical 200‒250 
WOOD ESTIMATED COVERAGE
(sq ft/gal)
Wood, New  125‒150 
Wood, Old 100‒125 
FIBERGLASS ESTIMATED COVERAGE
(sq ft/gal)
Fiberglass, New  200-250
Fiberglass, Old 175‒225 

CLEAN UP 

Use soap and water to clean tools and equipment.

Non–Acid Concrete & Masonry Cleaner is designed with Acid-Free Nano-Enhanced Technology, this cleaner quickly reacts with surfaces with deep penetration results. Designed to use on all types of masonry work. Including natural stone, brick, block, pavers, concrete floors, roof tiles and cementitious surfaces. Free from dangerous acids, alcohols, solvents or hazardous chemicals.

ADVANTAGES

  • Can be used indoors and outdoors
  • Nano-Enhanced for Fast Acting
  • VOC compliant with no harmful fumes
  • Eco-Friendly and Bio-Degradable
  • Non-Corrosive, Non-Flammable
  • Easy to rinse, with fast drying
  • Non-Flammable
  • It will not etch concrete.
  • Safe to use on colored concrete and stonework
  • 100% Water soluble

APPLICATION

Test Panel

Always try a small test area on each type of surface to ensure the proper dilution to ensure product suitability and efficacy. This will help determine the dwell time before scrubbing and rinsing. Heavy deposits may need repeated application and rinsing. Take note if the intended surfaces cannot with stand power washer pressure levels.

Application Temperatures

Surface temperature must be minimum low 50–90°F range when using this product. Temperatures below 50°F can reduce the effectiveness of this product.

Preparation

Cover and protect all surrounding areas where cleaning is not desired, to protect from over spray. Use poly or plastic drop cloth/tarps to cover and protect, glass, windows, plants, shrubs, lawn, vehicles and sidewalks from prolonged contact and over-spray.

Application and Coverage

Non–Acid Concrete & Masonry Cleaner is ready to use. Average coverage rate is 200-250 sq-ft per gallon.

Pre-wet surface areas with water before applying this product.

COVERAGE

MASONRY TYPE APPROXIMATE COVERAGE
(sq ft/gal)
Brick  150‒200
Limestone  100—150
Smooth (precast)  100—125
Rough Exposed Aggregate  80—125
Block (high density)  75—100
Block (low density)  50—75

 

Directions

CLEANING STEPS

Make a test panel before general cleaning. Protect and test all non-masonry surfaces. Reaction time will vary depending on buildup level. For all applications always apply bottom-to-top to avoid streaking. Apply using a pump-up sprayer, brush, or roller. Polyethylene (Garden or Hudson) or stainless-steel sprayers are recommended to avoid gradual breakdown of parts. For spot cleaning use trigger spray bottles.

Dilution: 1 part cleaner to 1 or 2 parts water.

Exterior Cleaning

  • Prewet surface.
  • Apply diluted cleaner onto the surface with an air-less spray pump.
  • Scrub surface with a soft, fibered masonry nylon brush.
  • Let set for 2‒3 minutes; Allow the cleaner to react, emulsify, and break down the deposits. Do not let cleaning solution dry on the concrete.
  • Rinse off with water or pressure washing equipment (3 gallons per minute at 600‒800 psi). Always use caution when using high pressure rinsing, take care to not damage the underlying surface. To avoid streaking, always keep lower area wet.
  • Repeat above steps until stains are removed.

Interior Cleaning

  • Provide adequate ventilation for air circulation.
  • Protect floor with poly film or another appropriate method. Protect plumbing fixtures, doorknobs, light fixtures, etc.
  • Follow the procedures above (exterior cleaning). If a water hose cannot be used, use a sponge or brush for rinsing. Thorough rinsing is a must.
  • Best practices dictate working on smaller, more manageable, areas to obtain the best results.

General Spot Cleaning

  • Spray diluted Non-Acid Concrete & Masonry Cleaner on the stain/spot and affected areas.
  • Wait 30‒60 seconds and scrub the stain/spot gently with a very soft nylon brush, then rinse.
  • If the stain/spot remains, repeat the above steps until the stain/spot disappears.

Note: Avoid applying water after removing dirt, stains & efflorescence, which would reactivate efflorescence inside the concrete or mortar.

Removal, Clean up & Resealing

Removal & Clean Up

After cleaning the surface, simply let the surface dry. If needed, sweep or brush clean.

Collect all dry waste material for proper disposal and dispose in compliance with Federal, State and local regulations. Use 5% baking soda solution to neutralize spills on the ground.

Resealing

Allow surface to dry completely before re-coating with a recommended EST Inc. sealer and waterproofing product to protect surface and to avoid reformation of efflorescence and to make future cleaning easier.

Contact EST Inc. representative for additional technical assistance and specific cleaning and water proofing product recommendations based on the surface.

Paint Equipment Cleaner-P2 is designed to clean paint guns, sprayers, nozzle and all paint-handling equipment.

This unique product is designed to clean and flush all types of paint handling equipment, like sprayer, supply line, pump, and paint mixers. It is safe on supply lines and all metal parts.  This product contains special anti rust additives and fast acting emulsifiers to remove dry and gummy paint residue from paint handling equipment.

FEATURES

Paint Equipment Cleaner is comprised of organic, terpene hydrocarbons and inorganic solvent blends to boost cleaning power without using flammable and hazardous solvents.

HOW IT WORKS

It works by lifting paint from the spray gun surface rather than dissolving it. If it is a closed system, it will re-circulate the solution through two filters to remove paint solids. This process effectively cleans the solution for extended periods of time. 

The cleaning solution is flushed through the paint gun in a similar way to other automatic paint-gun cleaners. The cleaning unit is equipped with continuous filtration to remove paint solids and refresh the cleaning solution. Filters are changed on average once per month to maintain the solution. Heavily-soiled paint guns and pots should be pre-cleaned to conserve cleaning solution.

Directions 

When cleaning pump and line pour Paint Equipment Cleaner in the pump let stand for 10 to 15 minutes then flush line by spraying. Repeat application if needed. Rubberized and harder to clean paint may require longer soaking time.

When cleaning dry and hard paint residue, soak equipment into this cleaning solution for 1 to 2 hours then remove loose residue by scraping or rinsing off with high-pressure water. Repeat above application if needed.

Plasticon-X Plasticizer Admix is a specially-formulated product for concrete, sand, and cement products.

Advantages

  • Increases compressive strength.
  • Minimizes efflorescence.
  • Speeds cycle time.
  • Helps to brighten colors.
  • Does not create moisture-probe problems.
  • Eliminates extra dispenser.
  • Helps green strength.
  • Resists primary “bloom or scum” formation in highly-colored units.
  • Provides lubricity and clean casting of concrete blocks, pavers, roof tiles, and precast concrete.

Directions

Plasticizer should be used at a rate of 18‒20 oz per 100 lb of Portland cement, depending upon the desired effect. (18 oz is recommended as an initial base). Add plasticizer to the batch mixture after water has been added; slight moisture adjustment may be required.

Note: Dosage amounts may need to be adjusted due to variation in mix design and aggregates. A higher use level will not affect the strength. DO NOT use other admixes. Plasticizer may be added to the batch manually or with an automatic pump.

To achieve proper dispersion of Plasticizer, allow a minimum of five minutes mixing time at full mixing speed.

SPECIFICATIONS
 Odor Sweet
 Weight/Gallon 8.63 lb/gallon
 pH 8.3
 Appearance Light yellow
 Solubility in H2O Complete

 

ASTM TEST DATA

Specifications for exterior walls.

ASTM C33 Normal weight aggregates.
ASTM C150 Portland cement.
ASTM C55 Grade N concrete block.
ASTM C145 Grade N solid loadbearing unit.
ASTM C90 Grade N hollow loadbearing unit.

Rust Converter Rust Coat rust treatment is a Nano-enhanced, anti-rust coating. It is a new development in destroying old rust on metal surfaces while preventing new rust from forming. It converts rust into a black, hard, shiny coating. It is water-based and VOC (Volatile Organic Compound) compliant.

Rust Converter Rust Coat is excellent for farm, construction, and institutional equipment, or any surface with rust. It is used in industrial settings, machine shops, waste treatment plants, city and county garages, hospitals, and at home.

EXCELLENT FOR

Machine Shops, Industry, Farm Equipment, Institutional Equipment, For any rusty surface, Waste Treatment Plant, City & County Garage, Construction Equipment, Hospital and Home

ADVANTAGES

  • Designed to use on all rusted surfaces.
  • Sanding of metal is not required.
  • Long lasting.
  • Easy to use.
  • Metal may be painted over after treatment.

APPLICATION

Use rubber gloves. Mix well before using. Apply the solution between 50°F and 90°F. Do not place unused material in the original product container. All surfaces should be dry and moisture free before applying this product.

No sanding is required, but for best results, lightly remove corrosion in rusted area with a wire brush. Clean off any remaining oil, dirt, or grease before application. Brush or sponge on liberally; careful application will result in a smooth finish.

After a few minutes, a black coating will begin to develop. Uneven color indicates additional applications are required for maximum protection (two coats are usually required). Apply a second coat 1‒2 hours after application of first coat.

For long-term protection and a smoother finish, use a primer and paint which can be lightly sanded; do not sand the black coating directly. Allow the coating to dry 24 hours before painting.

Clean up can be done with water and detergent.

DESCRIPTION AND USE

Safe Restore is a breakthrough detergent that provides remarkable versatility, cleaning power, and safety all in one product. It is capable of removing the deepest pollution and mineral and metal oxide stains from a wide variety of surfaces. It is an effective coating remover and safely cleans glass and anodized aluminum when used as directed. Safe Restore won’t damage or change the color of any of the substrates it is used on. Safe Restore is a great choice for cleaning historic buildings as well as modern facilities such as colleges, schools, hospitals, and other government and public facilities where safety is an issue. With its spray-on/spray-off application process, Safe Restore will save hours of cleaning time versus the traditional bucket and brush method.

Suitable Substrates: Brick, limestone, sandstone, concrete, precast, exposed aggregate, granite, unpolished marble, synthetic stone, terrazzo, anodized aluminum, EIFS, uncoated stainless steel, stucco, roofs, glass, and virtually any type of construction material. 

Stain Removal: Vanadium and manganese, any metal or mineral oxide stains, pollution stains, concrete leaching, caulk bleed, water-hardness stains, and sealer over-spray from glass, and sealants.

ADVANTAGES

  • Safe on glass when used as directed.
  • Safely cleans an anodized restoration.
  • Excellent for removing virtually all stains including mineral and metal oxide stains.
  • VOC compliant.
  • Low odor; can be used for interior cleaning.
  • Improves productivity.
  • Reduces liability.
  • Cleans multiple substrates.
  • Excellent for limestone, concrete, and brick.
  • Capable of removing failed topical sealants and some coatings.

LIMITATIONS

  • Do not use on polished marble and metallic oxide film used for tinting glass.
  • Not suitable for certain low-fire tiles when using an extended dwell time (always pretest small area first).
  • Do not allow product to dry on surface; always rinse thoroughly.
  • Not recommended for restoration antique glass, brass, coppe,r or bronze.

TECHNICAL DATA

Appearance and Odor Amber liquid, mild odor Boiling Point 212°F
Physical State Liquid Freezing/Melting Point N/A Specific Gravity (Water=): 1.1117
Vapor Pressure (mmHg) N/A Evaporation Rat Slower than ether
Vapor Density (air=1) N/A Solubility in Water Complete

Directions

SURFACE PREPARATION

Always test product in a small area first before beginning entire project. Test and protect adjacent and surrounding surfaces from exposure to the cleaning solution. Avoid direct contact with foliage. Use plastic to cover landscaping or wet the foliage with water before and after the cleaning process. 

Pretesting: Always test in an inconspicuous area prior to beginning full scale cleaning operations. Test cleaning effectiveness on each type of surface and stain.

Air Temperature: Excessively high or low temperatures will produce poor results. Best cleaning results are obtained when air and surface temperatures are between 40°F and 90°F. Do not clean when temperatures are below freezing or will be overnight. If freezing conditions exist, allow adequate time for surface to thaw. If air temperature exceeds 90°F, cool the surface with water before applying detergent. Do not allow product to dry on a hot surface.

Dilution: Use Safe Restore undiluted for most applications. Note: dilution of the product may be used based on test results, application, and the severity of the staining.

Application: Before applying read the Preparation section and Precautionary Measures under Safety Information. Recommended application is by low-pressure sprayer. Brushing is not necessary. One single, undiluted application will remove many stains. For deep stain removal and porous surfaces, prewet the surface with water. Then use a double, undiluted application, spaced several minutes apart without rinsing between applications. Follow with a pressure wash rinse of approximately 1,000 psi to 3,000 psi for the best results. Do not allow product to dry on the surface; always rinse thoroughly.

Coverage Rates: Coverage rates vary with an average of 75‒250 sq ft/gal depending on surface porosity, texture, and severity of staining.

PRODUCT DESCRIPTION

Safe-T-Strip is a biodegradable, VOC-compliant, non-solvent-based oil and grease remover, paint stripper and cleaner. It is designed to remove adhesives, black mastic, oil, grease, enamel- and latex-based paint, lubricants, and other petroleum-based coatings and residues from concrete, tile, brick, and all types of masonry surfaces. Safe-T-Strip is a safe alternative to hazardous citrus, terpene, and hydrocarbon-based chlorinated solvents.

FEATURES

VOC compliant. Non-flammable. Non-corrosive. Biodegradable.
Water cleanup. Very-low odor Indoor and outdoor use.

DIRECTIONS

PRECAUTION: Protect all surrounding non-intended surfaces such as glass, wood, metal, plastic, floors, and shrubs. If over sprayed, wipe off immediately. Keep away from open flame and heat. Do not dilute or alter this product, with other solvents or cleaners; use as is.

APPLICATION

Apply Safe-T-Strip directly to targeted surface by pouring, spraying (with low-pressure sprayer), brushing, or soaking in cleaner. Let soak for five to ten minutes before scraping. If residue becomes extremely thick, reapply, and scrape away softened material until final surface is visible. Use an auto-scrubber with black pad for faster stripping action. If residue remains, apply second coat, wait a few minutes, then scrape off final residue. Mop with EST’s H.D. Cleaner and rinse floor with water to ensure a clean surface; allow surface to dry.

For heavy stains, apply on effected areas by pouring or spraying. Wait 2–4 minutes while product penetrates oil stain. Scrub gently with brush and rinse with water by a high-pressure sprayer. For stubborn stains, repeat above steps until stain is removed. Use EST Inc.’s HD Concrete Cleaner to bleach any remaining gray shadowing. Apply EST Inc.’s HD Cleaner again to neutralize and rinse off excess residue from the cleaned surface. Let concrete dry completely; if shadow remains, repeat above steps to ensure complete stain removal.

STORAGE AND HANDLING

Consult material safety data sheet before using this product. May cause irritation; use with adequate ventilation. For industrial/professional use only. Applicators should ware neoprene rubber gloves, eye protection and rubber boots.

Keep product away from skin and eyes. Do not swallow or ingest this product. The use of rubber, neoprene, nitrile, or other protective gloves is required where prolonged or extensive use is expected. Remove contaminated clothing and DO NOT wear again until thoroughly cleaned. Wash hands thoroughly with soap and water after handling.

Keep container closed when not in use. Store out of direct sunlight. Keep from Freezing. Avoid temperatures above 100 °F, or below 40 °F. Product can be stored up to 12 months. If product is stored for a long time, lightly agitate, or shake well before use. This product is biodegradable and eco-friendly.

Note: Follow directions carefully. Always consult your dealer or supplier for timing, methods and to customize application, depending on contaminations

Silicone Mold Release -WB is a water- based mold-release agent that aids in releasing concrete castings from smooth-on rubber molds, plastic,fiberglass, and other blow-molding-type mold surfaces such as melamine, metal, and non-porous (sealed) wood. It provides a clean, positive, even release, does not interfere with color or surface detail, and helps minimize air holes and bubbles in finished castings. 

Advantages 

  • Low Cost; does not require dilution.
  • Water-based, eco-friendly: contains no VOC’s, carcinogens, or hydrocarbons harmful to the environment. 
  • Does not discolor or stain mold surfaces.
  • Does not affect detail or finishing. 
  • Minimizes pin holes and air bubbles. 
  • Will not soften, shrink, or swell  rubber, metal wood, plastic, or fiberglass molds.
  • Keeps molds clean; does not build up. 
  • Extends mold life.
  • Easy-to-use spray application.
  • Cleanup with water and soap.
  • Provides wet and dry surface release.

Technology 

Silicone mold release –WB is a Nano-enhanced and deep-penetrating mold release that chemically bonds to mold surfaces ensuring the highest number of releases per application with minimal transfer and no mold fouling. It eliminates rubber-to-metal bonding failures. 

Technical Data

Appearance and Color Milky white liquid pH Neat Neutral
Cold Stability 32°F Specific Gravity 1.02
Odor None Flash Point None
Solubility 100% Boiling Point N/A

Synacid-300 is the world’s only Nano-Enhanced Synthetic acid with cleaning properties that outperform traditional acids like Muriatic acid without any of the harmful effects. Synacid is non-D.O.T. regulated, non-fuming, 100% biodegradable, and OSHA and EPA compliant. Synacid-300 is also a safe alternative to acids and is listed at a triple zero Hazardous Material Index.

Synacid-300 Nano-Enhanced will dissolve and loosen the heaviest mineral or calcium deposit from metal pipes without harming or rusting the metal pipe and is designed to penetrate the toughest composites of mineral build-up. 

PHYSICAL PROPERTIES

APPEARANCE Light Yellow Color
WEIGHT/gallon 9.33+/-0.1
pH  <1
SOLUBILITY 100% in water
FLASH POINT  None
BOILING POINT 214°F

APPLICATION

Synacid-300 can be diluted with water depending on the amount mineral build-up. 

LIGHT DEPOSIT DILUTE 5:1 with water
MEDIUM DEPOSIT DILUTE 3:1 with water
HEAVY DEPOSIT DILUTE 1:1 with water
EXCESSIVE DEPOSIT USE UNDILUTED

STORAGE AND HANDLING

Synacid-300 Nano Enhanced has a storage life of one year. Keep container closed when not in use. As with all chemical products and materials take care as to where you store them. Safety glasses are suggested for use when handling this product.

Tile Seal 1000 WB is designed to apply on wet or dry concrete roof tiles.

ADVANTAGES

  • Penetrating sealer; does not leave film after it dries.
  • Reduces efflorescence.
  • Resists mold and mildew.
  • Does not change color of tiles.
  • Ready to spray.
  • Leaves a high-gloss finish on tiles.
  • UV-stable; retains the natural-looking color of tile.
  • Does not turn white.
  • Non-VOC.
  • Water based.
  • Safe to use.
  • Can be applied in multiple coats.
  • Can be applied on tiles even after installation on roof.

APPLICATION

Drying Time: Dry to touch less than 3 hours after application. Initial cure will be in 24 hours. Maximum cure will be reached within 7 days.

Application can be made with automatic sprayer or low-pressure sprayer using 10–20 psi and can be applied on tiles after they’ve been installed on a roof.

Clean Up: Clean all application equipment with hot water and cleaning detergent.

BENEFITS

  • Extremely durable with a long-lasting shine.
  • Nano–enhanced.
  • Easy to apply.
  • Solvent free.
  • Does not discolor.
  • Provides non-slip surface.
  • High-gloss finish.
  • Provides static control.
  • Creates a wet-look shine.
  • Chemical resistant.
  • Abrasion resistant.
  • Skid-mark resistant.
  • VOC compliant.
  • UV resistant.
  • Vinegar and mild acid resistant.
  • Extreme performer.
  • Provides exceptional strength

Technical Data

Appearance Translucent Dispersion Volatile Organic Compounds, by Weight
Type Aliphatic Polyester Polymer Triethylamine, % 1.4
Total Solids, by Weight 28% Free-Film Properties
Total Solids, by Volume 25% Tensile strength 7000 psi
 pH 7.5–8.0 100% Modulus 4000 psi
Viscosity, Brookfield 125 cps Elongation 300 %
Weight per Gallon @ 25°C 8.5 lbs. Slip Resistance ASTM-D-2047
Acid Number, on Solids 14/gm/L Dry Film Static Control 100%

DIRECTIONS

Clean floors so that all dirt and other foreign substance are removed. Allow the floor to dry. Apply this product with a microfiber pads or wax applicator. For an extremely long-lasting finish, three or four coats are recommended; floors can be burnished between each coat. Metal-wear finish does not need buffing. However, if buffing, wait 2–4 hours after application.

Note: For new floor tiles initially apply 4– 5 coats before burnishing. Use EST’s Neutral Floor Cleaner to neutralize floor surface before applying this finish. For daily maintenance, use EST’s Spray & Buff to revive glossy appearance.

STORAGE AND HANDLING

Keep product away from skin and eyes. Do not swallow or ingest this product. The use of rubber, neoprene, nitrile, or other protective gloves is required where prolonged or extensive use is expected. Remove contaminated clothing and DO NOT wear again until thoroughly cleaned. Wash hands thoroughly with soap and water after handling.

Keep container closed when not in use. Store out of direct sunlight. Keep from Freezing. Avoid temperatures above 100 °F, or below 40 °F. Product can be stored up to 12 months. If product is stored for a long time, lightly agitate, or shake well before use. This product is biodegradable and eco-friendly.

 Note: Follow directions carefully. Always consult your dealer or supplier for timing, methods and to customize application, depending on contaminations.